Easy Fix for Missing Drawer Pulls
I found this desk at a thrift store and fell in love with it at first sight! Overall it was in good condition except the center drawer was missing the drawer pull. No worries though -- there's an easy fix!
The first thing I did after bringing it home was to give it a good cleaning. I knew it was a vintage piece, but underneath the drawers I discovered date stamps showing the actual year it was built was in 1901. It was manufactured by the Widdicomb Furniture Company in Grand Rapids, Michigan. Each phase of the manufacturing process was stamped with the date and the name of the craftsman. This made the desk even more special to me.
I try to use good judgement when deciding whether to paint a piece or not. A previous owner had already painted it, so I figured it wouldn't hurt to paint it again.
I actually liked the painted finish except for the top as the brush stokes were a bit bumpy for a desk top. I did strip the paint from the top and stained it, but the stained finish turned out too blotchy, so I decided to proceed with painting.
But first I needed to address the missing drawer pull. Rather than sourcing a matching drawer pull, or instead buying three new pulls, I decided to use a single knob that I had left over from a previous project. So I needed to fill in the existing holes.
An easy way to fill in the existing holes is to first place painter's tape on the back of the hole.
Next I added a small amount of wood filler to a syringe. Using the syringe eliminates air bubbles which can cause the wood filler to crack after it dries.
Then I injected the wood filler into the holes. The tape I placed on the back of the hole earlier will hold the wood filler in place until it dries.
I applied additional wood filler to the surface and used a putty knife to smooth it out. After the wood filler was completely dry I used 220-grit sandpaper to sand it smooth. Next I used a power drill to add a single hole for the new knob (sorry no photos of this step because I needed both hands to use the drill!)
Although the replacement knob is not an exact match, I think it coordinates well with the existing hardware.
Here's a closer view of the replacement drawer knob.
Thanks for reading through this project. I hope you found the information helpful and if you'd like to see more photos, please visit my blog post. I'd also like to invite you to stop by my blog, The Black Sheep Shoppe, to see what other projects I am working on.
Please note the cost and time estimates for this project are just that -- estimates. I already had the knob, wood filler, tape, and the syringes on hand.
Enjoyed the project?
Resources for this project:See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info
Want more details about this and other DIY projects? Check out my blog post!
Published June 12th, 2018 9:12 AM
Frequently asked questions
Have a question about this project?
3 of 11 questions
Join the conversation
4 of 121 comments
Sharron Christie on Dec 08, 2020
Absolutely beautiful. I love the colour of the finish. I’m sure the furniture makers would be happy too!
Robyn Garner on Dec 08, 2020
Thanks much for the tip about using a syringe!
My Grandfather, Harry Cool, was a wood carver in a furniture factory in Grand Rapids, and I was sooo hoping to see his name. My mother (Harry's daughter) was the New Year's Baby in Grand Rapids --the first baby born in 1920! I have photos of that!
Your choice of color is absolutely stunning!! I would love to duplicate your finish on my next "find" (I could spend all day in antique stores, junk shops, flea markets, etc.).
I looked at your web page and your blog about this desk trying to find out the colors you used. I found the colors but I cannot find the brand of chalk paint you used. The link to the chalk paint & wax doesn't work. Would you mind sharing the brand(s) of paint & wax? Thanks!
Can you use wood filler or some sort of glue to fill in a hole on a wooden pull knob? I have an antique wooden knob for a dresser. It has a metal insert but I think it is stripped. The screw seems ok.